Special Order the Jet Teng Models Viper 90 mm EDF jet that features unparalleled detail and craftsmanship.  By purchasing this jet, please allow an estimated 3-4 weeks for delivery.  The jets are custom made per order at the factory.  The jet will be sent to our warehouse and then we will ship it to the buyer with tracking informaton. While the jet is at our warehouse, it will be inspected to ensure that there is no overseas shipping damage.  Then the jet will shipped to your house at this point.  The estimated time in the warehouse is 24 hours.

DETAIL INFORMATION:

    The Jet Teng Models Viper ARF is an edf jet that offers high performance and very high detail.  The jet is a full composite 90mm edf jet that features a fiberglass wing as well as a fiberglass fuse, fin, and stabilizer.  The detail work includes panel lines and rivet detail over the entire surface of the jet.  The jet comes prepainted from the factory with decals applied and a clear coat finish to protect the jet.

CONSTRUCTION INFORMATION:

   Along with the cosmetic detail of the Jet Teng Models, the engineering and construction detail rivals the appearance.  It is designed for a Schuebeler DS-51, HET 9305 and HET 9305-700 90mm fan units.  But can also take a Jetcat P20 Turbine. The front air inducting is factory installed and exhaust ducting is included.  Retracts are easy to install with mounts pre-installed in the nose and hatches ready for cut out in the wing. In addition, the canopy is glued together and all hatchwork is done at the factory with hatch locks installed.  Even the flying stabilizer is easy to attach to the fusalage with just four screws.  The plane features aileron, elevator, rudder,throttle and flap funtion standard.  Optional features would be retracts and nose gear steering.  The arf kit even comes with retract gear door covers.

BUILDERS NOTE: REFER TO THE "ELECTRIC SETUP GUIDELINE" ON THE HOME PAGE TO HELP DETERMINE THE PROPER SET UP FOR FAN, ESC, MOTOR AND BATTERY.

SPECIFICATIONS:

• EDF Size: 90 mm Schubeler DS-51, HET 9305 HET 9305-700 Fan Unit or Jetcat P20 Turbine
• Scale: 1/9
• Wing Span: 1410mm (55.5")
• Length: 1280mm (50.5'')
• Estimated flying weight: 8 lbs
• Recommended Power: 8-10S Li-Po System and Motor
• Brushless Motor: HET 600 or 700 Series Motor

ITEMS NEEDED FOR COMPLETION:

• Li-Po Battery: 8 to 10S 30C 4000 mAh or higher
• Brushless Motor
• ESC: High Voltage ESC
• Castle Creations Pro BEC
• 90 MM Fan Unit: Schubeler or HET 9305
• Servos:
• 3x Hitec HS-125MG for Ailerons, Rudder
• 2x Hitec HS-125MG for Flaps
• 1x Hitec HS-225 or HS-5245MG for Elevator

Optional servos:

• 1x Hitec HS-82 for Retracts
• 1x Hitec HS-225MG for Steerable Nose Gear
• 24 Inch Servo Extensions: x6
• 2 ft: Red and Black Silicone Wire
• Minimum 5 channel receiver and transmitter
• Landing Gear

OPTIONAL ITEMS:

Jet Teng Pneumatic Retract System(Not Included with arf)

• Air up and spring down for safety
• 1 servo needed for operation
• Weight: 250g/ 9 oz
• Total Plane Weight: 10-14 lbs.
• Length: 85mm/ 3.35 Inches
• Width: 42mm/ 1.65 Inches
• Height: 34mm/ 1.33 Inches

Jet Teng Oleo Struts feature an airbrake system installed(Not Included with arf)

• Machined aluminum oleo strut action
• Air Brake System
• Weight: 280g/ 10 oz
• Total Plane Weight: 10-14 lbs.